Product#: MM3059

1969-74 Chrysler 8-3/4" With 1-7/8 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...


Product#: MM3089

Mopar 8-3/4" Differential Cast Iron 10-Spline Rear Yoke (Uses 7260 Series Strap Retained U-Joint)

This cast iron yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3311 s trap kit, Note: Uses 7260 series U-joint (sold separately) that have a 2.125" snap...


Product#: MM3108

8-3/4" Adjustable Pinion Snubber

Designed to bolt on the top front of the axle housing, these Mancini Racing adjustable pinion snubbers help to eliminate axle twist and wheel hop by contacting the floor pan of the car. With several adjustment points, the...


Product#: MM3311

Mopar - Yukon Strap Kit - With 7260 U-Joint

These u-joint strap kits are designed for use on stock and Yukon pinion yokes with 7260 u-joint size. Includes: two straps and four bolts. Made in the USA.


Product#: MPN001

1968-69 Dodge Charger Differential Cover Bolts

New reproduction 3/8" hex flange bolts for use with 1968-69 Dodge and Plymouth models. Set includes 10 bolts total and fits several vehicles. See description below to ensure a proper fit on your Mopar. Dodge Applications:...


Product#: MN3161

1960-76 Mopar Rear End Housing E-Brake and Brake Line Clip Set

Reproduction rear and housing e-brake, and brake line clip set for all 1960-76 models. Replace your rusted originals with these correct replacements. Must be welded to the factory locations.


Product#: MD7114

Axle Nut Locking Pawl

This locking pawl and flanged nut is used on the right side axle of 8-3/4" and 9-3/4" differentials. The pawl secures the axle end play adjusting nut once proper bearing play is established.

Axle Nut Locking Pawl

MSRP $13.99 ea
Classic $11.99 ea

Product#: MN3361

Dana 60 Chrome Hex Head Differential Cover Bolt Set

This set is for use on Dana 60, or any other rear end using 3/8"-16 x 3/4" bolts. Includes 12 chrome finished bolts and 12 Flat washers (not chromed).


Product#: YSPPN028

Mopar 8-3/4" (Coarse Spline) Pinion Nut Washer

This pinion nut washer is for the Mopar 8-3/4" 10 spline pinion. FITS: Mopar 8-3/4", 41 Case Housing Mopar 8-3/4", 42 Case Housing Mopar 8-3/4", 89 Case Housing


Product#: MM3058

1960-69 Chrysler 8-3/4" With 1-3/4 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil...


Product#: MM3092

Mopar 8-3/4" Differential Billet Steel 10-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625" snap...


Product#: MM3057

1960-72 Chrysler 8-3/4" With 1-3/8 Pinion Stem Master Bearing Set

Yukon master overhaul kit for Chrysler 8.75" rear ends. Included in this kit are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and...


Product#: MM3093

Mopar 8-3/4" Differential Forged Steel 10-Spline Rear Yoke (Uses 1350 Series Strap Retained U-Joint)

This forged steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3310 strap kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625" snap...


Product#: MM3094

Mopar 8-3/4" Differential Billet Steel 29-Spline Rear Yoke (Uses 1350 Series U-Bol Retained U-Joint)

This billet steel yoke is manufactured specifically for Mopar differentials. Includes the yoke, and mounting hardware. Important: Use MM3307 u-bolt kit, Note: Uses 1350 series U-joint (sold separately) that have a 3.625" snap...


1960-1975 Mopar; 8-1/4" Rear End; Master Bearing Set With Timken Bearings
NEW

Product#: MM3104

1960-1975 Mopar; 8-1/4" Rear End; Master Bearing Set With Timken Bearings

Motive Gear master bearing overhaul set for Chrysler 8.25" rear ends. Included in this set are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shims, ring gear bolts, pinion nut, crush...


Product#: MM3100

1975-2000 Mopar; 8-1/4" Rear End; Master Bearing Set With Timken Bearings

Motive Gear master bearing overhaul set for Chrysler 8.25" rear ends. Included in this set are Timken carrier bearings and races, pinion bearings and races, pinion seal, complete shims, ring gear bolts, pinion nut, crush...


Product#: AR43732

5/16"-18 X 3/4" ARP Stainless Steel Differential Cover Bolt Set

Enhance the appearance of your rear end with ARP's stainless steel rear cover bolts. These bolts add a lustrous contrast to a painted OEM cover, compliment a chrome plated aftermarket version or add flash to that cast...


Product#: FDM101

Filtermag; Rear Differential Filter Magnet

FilterMag powerful rare-earth magnet traps and holds wear inducing metal particles smaller than 40-microns down to 1-micron. The super-strong magnetic force holds FilterMag to the cover, is reusable and will reduce...


Product#: MM3306

Mopar - Yukon U-Bolt Kit (W/ 1310 U-Joint) - 2 U-Bolts (3/8" X 1-11/16") & 4 Nuts

These u-joint u-bolt kits are designed for use on stock and Yukon pinion yokes with 1310 u-joint size. Includes: two u-bolts (3/8" X 1-11/16") and four nuts. Made in the USA. {fitment}


Product#: MD7120

Differential Pinion Thrust Spacer Set

Replacement thrust spacer set for 8-3/4" differentials with clutch type Sure-Grip prior to 1970. Required to provide axle thrust surface in four-spider differential applications. One set required per vehicle.