Product#: 153665B

Throttle Cable 36"" Cut-To-Fit; Stainless Steel; Black

This throttle cable is designed with a specially extruded liner to extend the life of the cable. Cables are equipped with aluminum fittings and aluminum ferrule to eliminate fraying. Clevis is designed to eliminate cotter...

Product#: TF700512

Spring Steel Rod Clip, Fits 1/4" Rod Diameter, RH, 17/64" ID.

Correct style rod clip used on various GM vehicles. Fits 1/4" rod diameter, RH, 17/64" ID. These reproduction transmission linkage rod clips need to be replaced when replacing your linkage rods. 1955-57 Chevrolet Transmission...

Product#: 14048

1958-88 Holley Carburetor Fuel Bowl Screw; 2-1/2"

Reproduction 2-1/2" flat blade carburetor fuel bowl screw for Holley carburetors. This special screw is specifically designed in the correct original configuration and head design for the early model Holley carburetors. Many...

Product#: 1256633

1955-79 Air Cleaner to Carb Gasket; 5-1/8".060" Thick; Various Models; Universal Fit

Reproduction air cleaner to carburetor gasket manufactured for use with any 2 bbl or 4 bbl carburator with a 5-1/8" base. Can be used with any small or big block engine. Fits most 1964 and newer Ford applications, most 1965...

Product#: 14305

Carburetor Fuel Bowl Screws; Set of 8; For Holley Carburetors

Reproduction set of 2-1/2" slotted head carburetor fuel bowl screws for Holley carburetors. These special screws are designed in the correct original configuration with the proper head design for the early model Holley...

Product#: TC10024A

Lokar 24"" Universal Stainless Throttle Cable with Stainless Steel Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: MN45060

1971 Dodge, Plymouth; Six Pack Installation Kit ; 440

This reproduction six pack installation kit comes with everything you need to hook up a big block six-barrel induction system. Kit includes throttle cable, fuel lines, coil bracket, linkage kit, choke, nuts, springs and...

Product#: 6593-BDVJ

Edelbrock Air-Fuel Ratio Monitor Narrow Band

The Edelbrock part #6593 Narrow Band LED Air-Fuel Ratio Monitor was designed for use with all aftermarket carburetor and EFI kits. The kit comes complete with an LED light display, oxygen sensor, sensor bung and wire harness....

Product#: 67108C-BCHW

Carburetor Main Body, For Use On Holley® 950 Cfm

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORMs 100% NEW, high-performance...

Product#: 67216-BCHW

Carburetor Main Body, Alcohol, For Use On Holley® 750 Cfm

Direct replacement components to turn a street carburetor into a high-performance carb: get that extra performance out of your ride in less than 30 minutes! Add up to 25-50 HP with PROFORM's 100% NEW, high-performance...

Product#: 67155-BCHW

Billet Throttle Base Plate: 650 Cfm, 700 Cfm, 750 Cfm, & 800 Cfm

Upgrade your carb with PROFORM's new Billet Throttle Base Plate! Made from solid billet construction versus die cast aluminum for added strength and durability this base plate comes with button torx head throttle plate...

Product#: 67156-BCHW

Billet Throttle Base Plate: 850 Cfm And 950 Cfm.

Upgrade your carb with PROFORM new Billet Throttle Base Plate! Made from solid billet construction versus die cast aluminum for added strength and durability this base plate comes with button torx head throttle plate screws,...

Product#: 67268-BCHW

Aluminum Throttle Base Plate, 650, 700, 750, 800 Cfm, Mechanical Secondary

Looking for an inexpensive replacement aluminum baseplate for you carburetor? PROFORM's new cast aluminum base plates are an inexpensive way to replace your existing plate, though we'd strongly suggest you consider upgrading...

Product#: DP10002A

Lokar Duo-Pak 36" Cut-To-Fit Stainless Steel Throttle Cable Set - Carbureted

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

Product#: MP700253

1968-69 Mopar Models with 426 Hemi Engine & 4-speed - Carter AVS Carburetor Dashpot and Bracket

Reproduction Carter AVS & AFB dashpot assembly and bracket for 1968-69 Mopar models with 426 Hemi for 4-speed applications. Dashpots help keep your car from stumbling when you suddenly lift off the throttle. The kit includes...

Product#: LK2133B

Lokar Polished Black Stainless Steel Throttle & Kickdown Cable Bracket for Edelbrock Carburetors

Lokar billet aluminum carburetor bracket and return spring kit for Edelbrock Carburetors. It attaches to both rear carb bolts to eliminate movement and ease the installation of Lokar's throttle and kick down cables. Made in...

Product#: TCP1048A

Lokar 48"" Cut-To-Fit Universal Polished Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis...

Product#: DP10001B

Lokar Duo-Pak 24" Cut-To-Fit Black Stainless Steel Throttle Cable Set - Carbureted

Lokar Duo-Pak throttle cable sets will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

Product#: DP10002C

Lokar Duo-Pak 36" Cut-To-Fit Throttle Cable Set with Black Nylon Housing - Carbureted

Lokar Duo-Pak throttle cable set will easily adapt to most gas pedals and throttle assemblies. Cable comes equipped with aluminum fittings and aluminum ferrules to eliminate fraying and feature a "U-Cut-to-Fit" outer housing...

Product#: MN1010

1969-72 Dodge, Plymouth; ;Air Cleaner Airbox to Baseplate Seal; with Air Grabber; Ram Charger

Repair the efficiency of the N96 Fresh Air system on Late-production 1969-72 Mopar B-body vehicles equipped with the N96 Fresh Air hood option. This option was referred to as the "Ram Charger" hood for Dodge models and the...

Product#: LK2134

Lokar Polished Stainless Steel Throttle & Kickdown Cable Bracket for Street Demon Carburetors

The Lokar Billet Aluminum Throttle/Kickdown Cable Mounting Bracket for Street Demon™ Carburetors is CNC machined from 6061-T6 billet aluminum. It provides easy installation of Lokar's Throttle and Kickdown Cables. Made...

Product#: TCP1048C

Lokar 48"" Cut-To-Fit Universal Polished Black Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" black polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative...

Product#: TCP1036A

Lokar 36"" Cut-To-Fit Universal Polished Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis...

Product#: MP700200

1966-71 Mopar With Hemi Engine - Original Carburetor Throttle Linkage

Replacement progressive throttle linkage for 1966-71 Hemi models with inline 2-4 barrel carburetors. Includes the correct plated ends, ball-end bolt for throttle cable and mounting bolt. Note: No further discounts apply.

Product#: TCP1024A

Lokar 24"" Cut-To-Fit Universal Polished Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis...

Product#: TCP1036C

Lokar 36"" Cut-To-Fit Universal Polished Black Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" black polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative...

Product#: 67162-BCHW

Aluminum Center Hung Float Bowl; For Holley®, Proform and Quick Fuel Technology Double Pump Carburetors

Lightweight aluminum center-hung fuel bowls with sight glass windows for easy visual float adjustment. Kit comes with two (2) fuel bowls and two (2) gaskets and anodized aluminum 5/8" x 18 inverted flare fuel inlets. {specs}...

Product#: TC10036A

Lokar 36"" Universal Stainless Throttle Cable with Stainless Steel Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: TC10048B

Lokar 48"" Cut-To-Fit Universal Stainless Throttle Cable with Black Stainless Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: 67166C-BCHW

Standard Replacement Billet Metering Block

Primary metering block for all 2300, 4150, 4160 models except carburetors with an accelerator pump transfer tube or reverse idle mixture system. Uses standard fuel bowl and metering block gaskets. Timed spark or ported vacuum...

Product#: OF5041K

1960-68 Chrysler Slant-6; 170-225 cid; Offenhauser Intake Manifold Linkage Kit; Dual-Quad

Get your carburetor to answer properly on demand with Offenhauser dual carb throttle linkage kits. Constructed for lasting service and dependability, the components are comprised of heavy-duty materials to engage your...

Product#: E1841

Edelbrock Thunder AVS Series® Models 1812/1813 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: TCP1024C

Lokar 24"" Cut-To-Fit Universal Polished Black Stainless Throttle Cable - Carbureted Models

This Lokar Hi-Tech "U-Cut-to-Fit" black polished stainless steel outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative...

Product#: TC10048C

Lokar 48"" Cut-To-Fit Universal Stainless Throttle Cable with Black Nylon Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: MD2599

1966-70 Hemi Choke Housing Set

Replacement choke housing set for all 1966-70 426 Hemi models. This set can be installed on any Carter AFB piston housing to create a functional choke. The set includes: Choke baffle plate, housing gasket, choke coil plate...

Product#: E1480

Edelbrock Performer Series® Models 1407/1410/1412/1413 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: E1486

Edelbrock Performer Series® Models 1403/1404/1801/1802/1803/1804 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: E1488

Edelbrock Performer Series® Model 1409 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: E1842

Edelbrock Thunder AVS Series® Models 1825 / 1826 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: TC10036C

Lokar 36"" Universal Stainless Throttle Cable with Black Nylon Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: VS1005

Lokar Vintage Series Carburetor 24" Throttle Cable - Black with Red Tracers

Lokar Vintage Series universal throttle cables for carbureted applications. This cut-to-fit cable features vintage inspired braided cloth jackets covering Lokar's specially extruded liners and stainless steel cabling. Made in...

Product#: E1489

Edelbrock Performer Series® Model 1411 Carburetor Calibration Set

This set includes a selection of metering rods, jets, and step up springs that allow fine tuning and calibration of Edelbrock Performer carburetors for mildly to extremely built motors, especially motors with performance...

Product#: 67222-BCHW

Performance Carburetor Rebuild Kit, Double Pumper Carbs 600-850 Cfm

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

Product#: MP15502

1969-71 Dodge, Chrysler; Carburetor Repair Kit; Carter 4-Barrel; AVS

Carburetor Repair Kit for your Carter 4-barrel AVS is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles, and...

Product#: MP15543C

1973-77 Dodge, Chrysler; Carburetor Repair Kit; Carter 4-Barrel; Thermoquad

Carburetor Repair Kit for your Carter 4-barrel Thermoquad is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles,...

Product#: TC10024C

Lokar 24"" Universal Stainless Throttle Cable with Black Nylon Housing - Carbureted

This Lokar Hi-Tech "U-Cut-to-Fit" outer housing with a "U-Cut-to-Fit" stainless inner wire throttle cable is designed with a specially extruded liner for extended service life and innovative clevis cable ends to eliminate the...

Product#: MP210133

1959-71 Chrysler/Dodge/Plymouth; Carburetor Repair Kit; 383 V-8; 2 Barrel

Reproduction of the original style carburetor components designed for use with 1959-71 Carter 2-barrel BBD carburetor. This kit is just what you need to rebuild the 2-bbl Carter carburetor on your 360, 361 & 383 V-8 engines....

Product#: MP210143

1960-73 Dodge, Plymouth; Carburetor Rebuild Set; 2 bbl Carter BBS; with "Flat" Accelerator Rod; 273, 318 V-8 & L6 Engines

Reproduction of the original style carburetor components designed for use with 1960-73 Carter 2 barrel carburetors. This kit is just what you need to rebuild the 2-bbl Carter BBS carburetor on your 273, or 318 V-8's and all 6...

Product#: TD2040

Carburetor Adapter; Holley 2BBL To Small 2BBL Manifold; 1/2"

1/2" Tall, Holley 2BBL to Small 2BBL manifold carburetor adapter cast aluminum. Trans-Dapt Performance carburetor adapters are designed to allow you to mount most carburetors on most manifolds to save you the expense of...

Product#: MP15435A

1968 Chrysler; Carburetor Repair Kit; Carter 4-Barrel; AVS

Carburetor Repair Kit for your Carter 4-barrel AVS is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles, and...

Product#: MP15271A

1965-67 Dodge, Chrysler, Plymouth; Carburetor Repair Kit; Carter 4-Barrel; AFB

Carburetor Repair Kit for your Carter 4-barrel AFB is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles, and...

Product#: 67224-BCHW

Performance Carburetor Rebuild Kit, Proform 850, 950 Cfm & Holley Hp Series

If you don't have hours to spend accumulating all these small parts, then PROFORM's performance rebuild kit is the perfect solution. The kit includes two size 110 machined needle and seat assemblies, needle and seat...

Product#: MF200

1968-69 383/440; 1968-70 340 Carter Avs 4-Barrel Choke Assembly

Replacement for the long extinct choke assembly for 1968-69 383/440 and 1968-70 340 Carter AVS equipped models. Has the correct part number ?45? stamped on the choke housing, ?Lean? and ?Rich? marks for adjustment. Yellow...

Product#: E2692

Carburetor Adapter, Open Center, Spread Bore Carburetor to Square Bore 4 Barrel Manifold; 2692

This Edelbrock carburetor adaptor is designed to mount 4-bbl Rochester Quadra jet carburetors to square-bore, single plane intake manifolds. The adaptor weighs two pounds and one ounce and ships via UPS. 2692 Specifications:...

Product#: MP15478B

1971-73 Dodge; Carburetor Repair Kit; Carter 2-Barrel; BBD

Carburetor Repair Kit for your Carter 2-barrel BBD is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles, and...

Product#: MP15395A

1967-69 Chevrolet, Dodge; Carburetor Repair Kit; Holley 2-Barrel; 2300, 2300G

Carburetor Repair Kit for your Holley 2-barrel 2300, 2300G is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles,...

Product#: MF653

1970-71 383/440 Carter Avs 4-Barrel Choke Assembly

Excellent reproduction of the Carter AVS choke assembly for 1970 383/440 and 1971 440 equipped models. Features the correct part number "53" stamped on the choke housing. Yellow chromate and zinc finished parts as original....

Product#: MP410135

1957-71 Chrysler/Dodge/Plymouth; Carburetor Repair Kit; 4 Barrel AFB

Reproduction of the original style carburetor components designed for use with 1957-71 Carter 4-barrel AFB carburetor. This kit is just what you need to rebuild the 4-bbl Carter carburetor on your 426 Hemi V-8 engine....

Product#: MP151068

1974-81 Dodge, Chrysler; Carburetor Repair Kit; Carter 2-Barrel; BBD

Carburetor Repair Kit for your Carter 2-barrel BBD is designed to restore your carburetors performance by replacing critical wear components that degrade over time. Each kit includes all gaskets, seals, jets, needles, and...

Product#: T2046

Carburetor Stud Set; 1-3/8"

We now offer a variety of stud sets to fit just about any Holley or Rochester carburetor. Set includes: 4 studs 4 nuts 4 washers For 2" set see part # T2047 For 3" set see part # T2106