Starter Bolt 3/8"-16 X 4-11/16"
Replacement starter bolt for models that require a 3/8"-16 x 4-11/16" bolt.
Reproduction starter splash shield or heat shield for various 1966-70 Dodge and Plymouth B-Body models. Many times missing and almost always rusted and in need of repair. This shield attaches to the LH front frame rail on...
Painless Remote Starter Solenoid Set
This set allows you to position the starter solenoid any place you need to in order to make maintenance easier, clean up an inner fender or just replace a factory starting circuit. Installation Instructions: Download Here Set...
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. The Hot-Shot Plus model includes...
Painless Hot Shot Plus Starter Solution; with Engine Bump Start Switch
Classic $51.99 ea
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
The solution for vehicles with GM starters that are hard to start when hot, or vehicles with old or worn out electrical systems. Works by boosting available amperage to the starter solenoid. Installation Instructions:...
Painless Hot Shot Starter Solution; without Engine Bump Start Switch
Classic $29.99 ea
GM Starter Bolt 3/8"-16 X 1-7/8"
Genuine GM starter bolt for various models. Replaces OE # 14097279 - starter mounting bolt (short) 3/8-16 x 1.87" (or 3/8"-16 X 1-7/8"). Fits most (non gear reduction) small block & big block chevy starters. Sold...
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Starter shield mounting bolt set for plastic starter shields. Each set includes (4) 1/4"-20 x 3/4" Serrated head bolts to mount PLASTIC K Frame and Starter Splash Shields on all 1966-74 auto trans models equipped with the...
1967-74 Dodge, Plymouth; Mounting Bolt Set; 4-Piece Set; For Plastic Starter Shields
Classic $8.99 ea
In today's high-heat environment, starters take in a lot of damaging heat that destroys the windings of the starter and solenoid. To combat this problem, we offer a non-conductive strap-on heat shield with a highly-reflective...
1964-74 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1964-74 Mopar models, excluding Hemi with Manual transmission. Each set includes studs, washers and all other hardware needed to mount the starter. Will not fit direct drive starter....
1968-74 Mopar Starter Dust Shield
Replacement starter dust shield for 1968-74 Mopar models. Mounts between starter and bellhousing.
Starter Bolt; 3/8"-16 X 4.33"; For 4.3L 5.0L 5.7L, or 502 Engine
Genuine GM starter bolts for various models. For 4.3L 5.0L 5.7L, or 502 Engine. Replaces GM Numbers 12338064, 09000852, or 10465167. Works with GM Performance 9000852 or 12606096 high-torque mini starters, also works with...
1966-69 Mopar Starter Mounting Hardware Set
Starter mounting hardware set for all 1966-69 Mopar models with a Hemi engine and manual transmission. This mounting set is for the direct drive starter that was used exclusively on 1966-69 manual Hemi models. Each set...
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Starter/transmission linkage splash shield for 1966-70 B-Body vehicles. Comes with 9 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5...
1966-70 Dodge, Plymouth B-Body; Starter / Automatic Transmission Linkage Splash Shield
Classic $11.99 ea
1962-65 Mopar B-Body Starter Splash Shield - Each
Reproduction of the original style starter splash shield designed for use on various Mopar B-body models. Each splash shiled is designed to replace the original exactly. Die-cut to exact dimensions and ready to install. Sold...
1966-68 Charger, Coronet, GTX, Road Runner, Satellite; Ignition Switch Bezel; Chrome; 7/8" ID
Reproduction of the ignition switch bezel for various 1966-68 Dodge Charger, Coronet, and Plymouth Belvedere, GTX, Road Runner, and Satellite models. Replace the scratched, pitted, damaged bezel with this quality reproduction...
1966-68 Charger, Coronet, GTX, Road Runner, Satellite; Ignition Switch Bezel; Chrome; 7/8" ID
Classic $13.99 ea
Starter/transmission linkage splash shield for A/B Body vehicles. Comes with 10 staples and a drill bit for installation. Original factory assembly line manual shows 9 staples to be used but we have seen anywhere from 5 to 7...
1963-66 Dodge, Plymouth A-Body; 1962-65 B-Body; Starter / Automatic Transmission Linkage Splash Shield
Classic $11.99 ea