Product#: 9275A

1960-68 Mustang, Falcon, Comet; Fuel Tank Sending Unit; w/o Low Fuel Warning; 3/8" Pipe; Zinc Plated

The most accurate reproduction fuel tank sending unit in the industry. Features the original design including a brass float, O ring, and filter that replicate the original in appearance and functionality. This unit monitors...

Product#: C67808

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 39" Long; For 1" Wide Straps

Universal style anti squeak cushions are designed to install between the gas tank and the gas tank straps. These fuel tank anti squeek pads cushion the gas tank from the body and straps to reduce noise caused by metal to...

Product#: 9275AB

1964-68 Ford Mustang; Fuel Tank Sending Unit; without Low Fuel Warning; 5/16"

Reproduction fuel tank sending unit for 1964-68 Ford Mustangs and other various models. The most accurate reproduction fuel tank sending unit in the industry, with original design brass float and filter. This unit monitors...

Product#: 9202A

1948-86 Ford; Fuel Tank Sending Unit Brass Float; Various Models

Reproduction of the original style and correct brass float for use with various 1948-86 Ford and Mercury models as listed below. This sending unit brass float is desirable for its long-lasting dependability as it lasts much...

Product#: CX5042

1965-97 GM; Fuel Tank Sending Unit; 0-90 Ohm; Universal Fit; For 6" to 24" Deep Fuel Tanks; Without Pick-Up Tube

Universal fuel tank sending unit for various 1965-97 Chevrolet and GMC trucks with custom tank under the bed and other GM models 1965 and later, that require a 90 ohm sender. Designed for use with OE or aftermarket 0-90 ohm...

Product#: 9034BR

1967-68 Ford Mustang; Fuel Tank Filler Neck

Reproduction fuel filler neck for 1967-68 Mustang. This filler neck is manufactured to factory specifications and replaces the original exacty. Will mount to the tail light panel and connects the filler hose to the fuel tank....

Product#: K915

Universal Fuel Tank Anti Squeak Rubber Set; Various Models: 24" Long; For 1" Wide Straps

Reproduction fuel tank anti squeek set for vehicle models. Includes one 5-1/4" x 2" x 1/2" precision die cut neoprene tank to floor cushion, two 24" x 1-1/4" molded rubber strap to tank cushions, and two 24" x 2 " x.060" flat...

Product#: T76063

Billet Aluminum; Fuel Filler Neck; with Pop-Up Gas Cap

Billet aluminum flush mount fuel filler neck with pop-up gas cap is the perfect addition to your classic car or truck when adding a non-stock fuel filler location or relocating your fuel tank. Features a super sanitary and...

Product#: 9047A

1967-70 Ford Mustang; Rubber Filler Neck Hose; Fuel Tank to Filler Pipe; 4-7/8" Long; 2-3/16" id

Reproduction fuel filler hose that seals the inlet filler neck to the fuel tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...

Product#: HK238-CM

1965-73 Ford Mustang; Screw Set; Gas Tank Mounting; 13 Piece Set

This 13 piece set contains all the mounting hardware needed to install your gas fuel tank. Each piece is factory correct. Screws and bolts are all fabricated from heavy-duty steel and coated to prevent any corrosion. Ford...

Product#: HK208

1964-70 Ford/Mercury; Wire Clamps; For Fuel Filler Neck Hose

Reproduction wire-style fuel tank filler neck clamps for 1964-70 Mustang, 1967-70 Cougar and 1966-70 Fairlane models. If your hose is loose, the filler neck clamps could be worn out and require replacing. These clamps are...

Product#: P9275A

1960-68 Mustang, Falcon, Comet; Fuel Tank Sending Unit; without Low Fuel Warning; 3/8" Pipe; Stainless

Stainless steel reproduction of the fuel tank sending unit featuring the original design with a brass float, O-ring, and filter that replicate the original in appearance and functionality. This unit monitors the fuel level in...

Product#: TK0120

Fuel Tank Sending Unit; 5 Hole; Early Ford, AMC, and Mopar; 73-10 Ohm

Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...

Product#: TK0121

Fuel Tank Sending Unit; 5 Hole; "Universal" 240-33 Ohm; For Many Aftermarket Gauges

Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...

Product#: HK21

1964-69 Ford Mustang; Hex Head Screw Set; For Fuel Filler Neck; 5 Piece Set

Reproduction fuel filler neck screw kit. Each 5 piece screw kit includes the hex head screws that are required to mount the fuel filler neck to the tail lamp panel on 1964-69 Mustang models. #10 x 1/2" Lg Tapping Screw with...

Product#: 9276B

1960-97 Ford, Mercury; Fuel Tank Sending Unit O-Ring; Various Models

Our synthetic rubber fuel sending unit oring gasket seal is produced to be resistant to heat, oil and chemicals. Features superb elasticity and bonding capabilities to ensure that it will not lose its shape over time. Will...

Product#: 9276A

1960-97 Ford, Mercury; Fuel Tank Sending Unit Retaining Lock Ring; Three Tab Style

Reproduction fuel sending unit retaining lock ring for various 1960-97 Ford & Mercury models. Each ring is manufactured in quality stamped steel for an original fit. Twists into place in the fuel tank to secure the sending...

Product#: 153350

Hex Washer Head Bolt; Type F Thread Cutting; 3/8-16" x 1 3/4"; Each

Reproduction zinc chromate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 3/8-16" x 1 3/4"...

Product#: 265385

EFI Fuel Return Adapter Set

When converting a carbureted vehicle to an EFI system that requires a fuel return system, there's no longer any need to buy an expensive fuel tank. This adapter creates a return system simply by cutting a 2-3/4" section out...

Product#: TK0122

Fuel Tank Sending Unit; 5 Hole; "Universal" 10-180 Ohm; For VDO Gauges

Our universal fuel tank senders mount with five mounting screws. They work on fuel tanks from 6 to 24 inches deep by cutting to length using the instructions included. Since fuel tank senders only read resistance to ground...

Product#: FTA45111

Universal Fuel / Gas Tank Return Line Fitting Conversion Install Kit; -6AN to 1/4 in. NPT

If you are installing an in-line fuel pump or an aftermarket fuel-injection setup but are using an original fuel tank not originally provisioned for a return line, this universal return line fitting kit is a simple and...

Product#: 9276C

1960-97 Ford, Mercury; Fuel Tank Vapor Separator Vent; Includes O-Ring Seal and Lock Ring; Various Models

This fuel tank block of plate set fits various 1960-97 Ford and Mercury vehicles with a 2-3/4" diameter fuel tank sending unit opening. Works great for custom fuel injection set ups where the stock fuel tank sending unit is...

Product#: 9034BRC

1967-68 Ford Mustang; Fuel Filler Neck; For 22 Gallon Conversion

When converting your 1967-68 Mustang from an original style 16-gallon tank to a 22-gallon fuel tank, the original filler neck will no longer work and must be replaced. This new conversion style filler neck is designed to be a...

Product#: AM9109

Autometer; Universal; Fuel Signal Adaptor for Autometer Gauges;

The Fuel Bridge wires in between your fuel level gauge and sending unit and allows you to use any AutoMeter fuel level gauge with any stock or aftermarket sending unit. The triple push button with LED display allows for easy...

Product#: 19161

Holley Sniper EFI; Fuel Tank Sending Unit; 0-90 Ohms

Sniper EFI fuel gauge senders are a big help during your installation. They can be used as a replacement for your existing unit. Or if you decide to upgrade your dash to aftermarket gauges, we have a sending unit with the...

Product#: 9034E

1964-72 Eleanor Mustang; Aluminum Fuel Filler Pipe; for use with Flip Top Gas Cap; Universal

This filler neck is required when using our 9030B aluminum flip top gas cap. Filler neck is sold individually. Flip top gas cap (9030B) and filler hose (9047E) available separately. Flange measures 5"; filler pipe 2" OD....

Product#: 9355

1964-68 Mustang; Fuel Pump Filter Canister

Reproduction of the original style direct-fit fuel filter canister is concours correct with original red silk-screened FoMoCo logo and other authentic markings. Used with filter mounted on fuel pump. Fits other models in the...

Product#: FTA45113

Universal Fuel / Gas Tank Return Line Fitting Conversion Install Kit

If you are installing an in-line fuel pump or an aftermarket fuel-injection setup but are using an original fuel tank not originally provisioned for a return line, this universal return line fitting kit is a simple and...

Product#: M265

Aluminum Flip Top Fuel Cap Gasket; Universal

Rubber gasket for use with our custom aluminum flip top gas cap. Measures 5-1/8" OD, 3-1/4" ID. Six bolt pattern, 4-1/2" center to center. {fitment}

Product#: TS64099

1964-70 Mustang Stainless Steel Gas Tank Mount Hardware Kit

Stainless Steel accessory bolt kits from Totally Stainless. These kits are a great compliment to Totally Stainless' line of body kits. They contain specialty fasteners not included in their body kits to finish off the look.

Product#: 567PL

1/4"-18 Hex Head Drain Plug;

Replacement hex head drain plug is 1/4"-18 thread.

Product#: 566PL

1/8"-27 Hex Head Plug

Replacement drain plug is 1/8" PT - 27 thread.

Product#: 9076A

1964-73 Ford/Mercury; Fuel Tank Filler Pipe Neck To Body Gasket

Reproduction of the original gas tank filler neck gasket for 1964-73 Mustang and 1967-68 Cougar models. The fuel tank-to-body gasket will ensure a leak free seal between your filler neck and gas tank. Replaces OE # C5ZZ-9076....

Product#: A2369

#10 x 1/2" Lg Tapping Screw with 5/16" Hex Washer Head; Zinc

Product#: 153349

Hex Head Sems Screw; With Washer; A/AB Point; 6.3-1.81 x 25mm; Black Phosphate; Each

Reproduction black phosphate fuel tank strap bolt for various models including 1974-81 Camaro and Firebird models. This bolt is designed to replicate the original design for an authentic appearance. Measures 6.3-1.81 x 25mm...

Product#: AM3262

Auto Meter Universal Fuel Tank Sending Unit; 240 Ohms Empty, 33 Ohms Full

This is a universal 5-bolt fuel sending unit for use with Auto Meter universal fuel gauges. This unit is not included with the gauges packages and must be purchased separately. It is used with gauges that require 240 ohms...

Product#: 9275N

1967-73 Mustang, Cougar; Low Fuel Warning Sensor

This Low Fuel Warning Sensor has a factory style that is designed replace the original in your Mustang of Cougar model. It sends a signal to the fuel light in your Mustang's gauge if your fuel is low. Restores original...

Product#: 9A011A

1957-89 Ford, Mercury; Fuel Tank Sending Unit Filter; with 5/16" Line; Various Models

Correct replacement of the original fuel tank float strainer filter for use with various 1957-89 Ford and Mercury models as listed below. This filter will keep dirt and other elements from clogging or entering the fuel...

Product#: 9A011B

1964-73 Ford Mustang; Fuel Sending Unit Filter; With 3/8" Tube

Reproduction of the original style sending unit filter designed to replace the old or worn out original filter on the fuel tank sending unit. Over time, the filter will wear out potentially causing problems with your fuel...

Product#: 9047F

1964-67 Mustang, Falcon, Cougar, Comet; Fuel Tank to Filler Pipe Hose; Nitrile 70 Shore;

Reproduction fuel filler hose that seals the inlet filler neck to the fuel tank stub neck. This hose will eliminate gas fumes from entering in the interior or trunk area when properly installed. Produced with correct high...

Product#: CX2140

Universal Flush Mount Fuel Filler Kit

This universal flush mount fuel filler kit can be used on any applications. The polished stainless steel filler is ideal for fuel tank conversion. Features a tethered cap, cap key, and 3 mounting holes for an easy...