Product#: ST779D

Bow Tie Exhaust Tip; Polished Stainless Steel; Twin Bow Tie Design; 13.8" Long; With 2.25" Inlet

This universal fit twin Bow Tie shaped exhaust tip is designed to install on nearly any Chevrolet car or truck with 2.25" diameter tailpipe. Crafted from high-quality 304 stainless steel, it is stamped in to the shape of a...

Product#: 9A603R

1964-67 Mustang, 1967 Cougar; Heat Riser Shroud & Tube Assembly

Reproduction Heat Riser for 1964-67 Mustang & 1967 Cougar models equipped with 260-289 ci engine and factory original air cleaner assembly. This stamped steel heat shroud and tube connects the exhaust manifold and then to the...

Product#: ST779A

Bow Tie Exhaust Tip; Polished Stainless Steel; 9" Long; With 2-1/4" Inlet

This universal fit exhaust tip is designed to install on nearly any Chevrolet car or truck with 2-1/4" diameter tailpipe. Crafted from high-quality 304 stainless steel, it is stamped in to the shape of a Chevrolet Bow Tie and...

Product#: ST779C

Bow Tie Exhaust Tip; Polished Stainless Steel; 9.25" Long; With 3" Inlet

This universal fit exhaust tip is designed to install on nearly any Chevrolet car or truck with 3" diameter tailpipe. Crafted from high-quality 304 stainless steel, it is stamped in to the shape of a Chevrolet Bow Tie and...

Product#: ST779B

Bow Tie Exhaust Tip; Polished Stainless Steel; 9.25" Long; With 2-1/2" Inlet

This universal fit exhaust tip is designed to install on nearly any Chevrolet car or truck with 2-1/2" diameter tailpipe. Crafted from high-quality 304 stainless steel, it is stamped in to the shape of a Chevrolet Bow Tie and...

Product#: RH160052

1964-68 Ford Mustang; American Racing Headers; Small Block 289-302; 1-3/4" Long Tube With 3" Collectors

American Racing Headers for Ford Mustangs with small block engines. They are fabricated from aircraft quality T304 stainless steel and feature 3/8? thick round port flanges with hand ported inlets and fully welded custom...

Product#: RH160053

1964-68 Ford Mustang; American Racing Headers; Small Block 289-302; 1-5/8" Long Tube With 2-1/2" Collectors

American Racing Headers for Ford Mustangs with small block engines. They are fabricated from aircraft quality T304 stainless steel and feature 3/8? thick round port flanges with hand ported inlets and fully welded custom...

Product#: HK6209C

1967-70 Mustang/Cougar; Boss 302; Hooker; Super Competition Ceramic Coated Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: E5225

1967-68 Ford Mustang; Eleanor; JBA Side Exhaust Kit; 2.5"; Stainless Steel

JBA Exhaust Systems deliver performance exhaust systems. This kit has power, sound and quality. The 2-1/2" piping is manufactured with mandrel bent stainless steel tubing. The exhaust tips are 4" double walled and ceramic...

Product#: HH82300

1964-73 Mustang 260-351W Hedman 1-5/8" Full Length Headers; Stainless Steel

Hedman Hedders stainless steel 1-5/8" full-length long-tube headers. They are constructed from 304 stainless steel for superior heat and corrosion resistance. These headers feature 16 gauge mandrel-bent primary tubing, laser...

Product#: HK6901B

1964-77 Ford/Mercury; 255-302W/351W; Hooker; Super Competition Black Ceramic Coated Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: 402655

1965-70 Ford Mustang; 260-428 V8; JBA Header Back Dual Exhaust System; 409 Stainless Steel; Under Rear Valance

When it comes to performance exhaust systems, most people are looking for three things: Power, sound, and quality. JBA Exhaust Systems deliver the best of all three, giving it both great looks and performance. One of the...

Product#: FM17282

Flowmaster; American Thunder; 1967-70 Mustang; V8; Crossmember-Back Exhaust System; For No Valance Cut-Outs

For the person who is looking for a complete Header-Back dual exhaust system with an aggressive tone. With easy fit in mind, this system is mandrel bent for maximum performance and include specially selected mufflers....

Product#: HK6114C

1967-70 Ford/Mercury; 390/427/428CI; Hooker; Super Competition Silver Ceramic Coated Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: A7400161

1965-70 Ford Mustang; Convertible; V8; Pypes 2.5" Crossmember-Back Exhaust; With X-Pipe & Violator Mufflers

Pypes 1965-70 Mustang Convertible V8 2-1/2" crossmember-back exhaust kit is designed to deliver enhanced performance, provide an extra punch in the passing lane and improve gas mileage. Precision matched mufflers, X-pipe and...

Product#: HH88306

1964-73 Mustang 260-351W Hedman 1-5/8" Full Length Headers; HTC Polished Ceramic Coating

Hedman Hedders 1-5/8" full-length long-tube headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature 16 gauge mandrel-bent primary tubing, laser cut 3/8"...

Product#: HH83668

1964-73 Mustang 351W Hedman Elite 1-5/8" Full Length Swap Headers; Black Maxx Ceramic Coating

Hedman Hedders Elite Ultra-Duty 1-5/8" full-length headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature thick-wall 14 gauge mandrel-bent primary tubing,...

Product#: HH88658

1964-73 Mustang 351W Hedman Elite 1-1/2" Mid Length Swap Headers; Matte Silver Ceramic Coating

Hedman Hedders Elite Ultra-Duty 1-1/2" mid-length headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature thick-wall 14 gauge mandrel-bent primary tubing,...

Product#: HK6208

1964-70 Mustang/Cougar; 351W; Hooker; Super Competition Black Painted Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: HH88408

1964-73 Mustang 260-302 Hedman Elite 1-1/2" Shorty Headers; Matte Silver Ceramic Coating

Hedman Hedders Elite Ultra-Duty 1-1/2" Shorty headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature thick-wall 14 gauge mandrel-bent primary tubing, laser...

Product#: HH83658

1964-73 Mustang 351W Hedman Elite 1-1/2" Mid Length Swap Headers; Black Maxx Ceramic Coating

Hedman Hedders Elite Ultra-Duty 1-1/2" mid-length headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature thick-wall 14 gauge mandrel-bent primary tubing,...

Product#: A7400158

1964-70 Mustang Convertible V8 Pypes 2.5" Crossmember-Back Exhaust w/ X-Pipe & w/o Mufflers

Pypes 1964-70 Mustang convertible V8 2-1/2" stainless steel crossmember-back exhaust kit is designed to deliver enhanced performance, provide an extra punch in the passing lane and improve gas mileage. Precision matched...

Product#: 9430J

1964-73 Ford Mustang; Performance Exhaust Headers; 6 Cylinder 170; 6-Into-1

Delivers a horsepower increase on 1964 - 1973 170, 200 or 250 cubic inch engines. Includes gaskets & hardware Will require AC compressor relocation if equipped. Only OE Ford factory starter motors/factory reconditioned...

Product#: F15937

Flowmaster; Universal; 3" U-Fit Aluminized Dual Exhaust Pipe Set

This set comes with all the pipes you need to build a custom dual exhaust system. Set includes: Front Pipes Mid Pipes Rear Pipes Side Exit Pipes Corner Exit Pipes Over-Axle Pipes H-Pipe Stubs Straight Crossover Pipe Bent...

Product#: HK6114

1967-70 Ford/Mercury; 390/427/428CI; Hooker; Super Competition Black Painted Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: A7400150

1965-70 Mustang Coupe/Fastback V8 Pypes 2.5" Crossmember-Back Exhaust w/ X-Pipe & w/o Mufflers

Pypes 1965-70 Mustang V8 2-1/2" crossmember-back exhaust kit is designed to deliver enhanced performance, provide an extra punch in the passing lane and improve gas mileage. Precision matched mufflers, X-pipe and OEM style...

Product#: HP175115

Heatshield Products; Armor Exhaust Heat Insulation; 1/2 Thick; 18" x 10 Feet

Exhaust heat wraps were just upgraded, up armor your exhaust heat insulation with Heatshield Armor. Heatshield Armor can reduce radiant heat from your exhaust pipe by 70%. The outer armor of this exhaust heat shield allows it...

Product#: P1094

Pypes Performance X-Change 3" Crossover X-Pipe; Polished 304 Stainless Steel

X-Change X-Pipes allow you to open and close your exhaust with the bolting or unbolting of dump plates. By exiting before the mufflers, you will make even more power! Because V8's fire unevenly, exhaust exits in pulses rather...

Product#: 13250C

2.50 Inch QTP Screamer Twintronic Muffler 13.5" Case

With the success of our Electric Cut Out we took it to the next level, The Screamer. A dual mode muffler with a single inlet with a dual outlet. One outlet is a straight pipe with our electric valve at the end on a 360 degree...

Product#: F15935

Flowmaster; Universal; 2-1/4" U-Fit Aluminized Dual Exhaust Pipe Set

This set comes with all the pipes you need to build a custom dual exhaust system. Set includes: Front Pipes Mid Pipes Rear Pipes Side Exit Pipes Corner Exit Pipes Over-Axle Pipes H-Pipe Stubs Straight Crossover Pipe Bent...

Product#: 13302C

3.00 Inch QTP Screamer Twintronic Muffler 10" Short Case

With the success of our Electric Cut Out we took it to the next level, The Screamer. A dual mode muffler with a single inlet with a dual outlet. One outlet is a straight pipe with a valve at the end on a 360 degree floating...

Product#: 13252C

2.50 Inch QTP Screamer Twintronic Muffler 10" Short Case

With the success of our Electric Cut Out we took it to the next level, The Screamer. A dual mode muffler with a single inlet with a dual outlet. One outlet is a straight pipe with a valve at the end on a 360 degree floating...

Product#: 13253C

2.50 Inch QTP Reverse Internals Screamer Twintronic Muffler 10" Short Case

With the success of our Electric Cut Out we took it to the next level, The Screamer. A dual mode muffler with a single inlet with a dual outlet. One outlet is a straight pipe with a valve at the end on a 360 degree floating...

Product#: HP175304

Heatshield Products; Armor Exhaust Heat Insulation; 1/2 Thick; 36" x 4 Feet

Exhaust heat wraps were just upgraded, up armor your exhaust heat insulation with Heatshield Armor. Heatshield Armor can reduce radiant heat from your exhaust pipe by 70%. The outer armor of this exhaust heat shield allows it...

Product#: HP325100

Heatshield Products; Inferno Header Exhaust Wrap 2 In x 100 Foot Roll

Tired of that "Brand X" 2000F header wrap becoming brittle and falling apart? Look no further than our Inferno Header Wrap to solve the problem. Unlike fiberglass and basalt (volcanic) exhaust wraps (which should be...

Product#: 5255C2

1967-69 Ford Mustang; GT; High Flow Dual Exhaust Tips; 2.5"

High flow exhaust tips for 1967-69 Mustang GT models. These high performance exhaust tips are made out of 304 stainless steel with the original contours to look just like the originals from the outside, but flow much better...

Product#: HH88660

1964-73 Mustang 351W Hedman 1-5/8" Full Length Swap Headers; Uncoated

Hedman Hedders 1-5/8" full-length headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature 16 gauge mandrel-bent primary tubing, laser cut 3/8" flanges, and...

Product#: HK6920

1967-70 Ford/Mercury; 351C; 4BBL; Hooker; Super Competition Black Painted Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: H8403

1964-73 Mustang, Falcon, Torino; 260-351W SBF; Patriot Long Tube Header; 1 5/8" Primary; 3" Collector; Plain Steel

Patriot full-length chassis and fender well headers provide the ultimate in performance for street rods and muscle cars with high performance engines. The key is their use of long primary tubes, which results in more...

Product#: HH88300

1964-73 Mustang 260-351W Hedman 1-5/8" Full Length Headers; Uncoated

Hedman Hedders 1-5/8" full-length long-tube headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature 16 gauge mandrel-bent primary tubing, laser cut 3/8"...

Product#: HH88400

1964-73 Mustang 260-302 Hedman 1-1/2" Shorty Headers; Uncoated

Hedman Hedders 1-1/2" Shorty headers. They are constructed from heavy duty mild steel for superior durability and wear resistance. These headers feature 16 gauge mandrel-bent primary tubing, laser cut 3/8" flanges, and 3"...

Product#: HK6901

1964-77 Ford/Mercury; 289-302W/351W; Hooker; Super Competition Black Painted Full-Length Headers

With Hooker Super Competition headers the objective has always been to make the maximum horsepower and to put it at the optimum point in the power curve. It takes a lot of time and money to do the job right. We will sometimes...

Product#: FT12119

1965-70 Mustang; 260-302; Flowtech; 1-1/2" Tri-Y Headers; With Black Painted Finish

Flowtech Tri-Y long-tube headers for 1967-70 small block powered Mustangs. The 4-2-1 design features 16-gauge 1-1/2" primary and 1-3/4" secondary tubing feeding into a 2-1/2" collector. These header is coated in a high heat...

Product#: 55106S

Gibson CFT Superflow Muffler; Stainless Steel; 4" x 9" x 18" Oval Body; 2.5" Dual Inlet; 2.5" Dual Outlet.

Gibson's CFT Superflow muffler with Convergent Flow Technology actually tunes your exhaust by using resonance chambers, directional louvered tuning ports and angular induction to draw exhaust gases into the muffler and expel...

Product#: F15923

Flowmaster; 3.5" Collector To 3" System; Header Collector Ball Flange Set

This header collector set takes the place of messy three-bolt, flange-type connections and allows for a leak-free and gasket-free ball-flange type connection. Made in USA Emission Note: 50- State Legal This part is legal for...

Product#: RE1023B

POR-15 High Temp; Heat-Resistant Paint; Manifold Gray; 1 Gallon

POR-15 High Temp Heat-Resistant Paint is capable of withstanding extreme temperatures up to 1200°F / 648.8°C and will resist cracking, chipping, and peeling. This high temperature coating is also extremely weather,...

Product#: RE1023C

POR-15 High Temp; Heat-Resistant Paint; Aluminum; 1 Gallon

POR-15 High Temp Heat-Resistant Paint is capable of withstanding extreme temperatures up to 1200°F / 648.8°C and will resist cracking, chipping, and peeling. This high temperature coating is also extremely weather,...

Product#: RE1023A

POR-15 High Temp; Heat-Resistant Paint; Black Velvet; 1 Gallon

POR-15 High Temp Heat-Resistant Paint is capable of withstanding extreme temperatures up to 1200°F / 648.8°C and will resist cracking, chipping, and peeling. This high temperature coating is also extremely weather,...

Product#: F52571

Flowmaster; 70 Series Muffler; 22" Length; With 2-1/2" Offset Inlet; 2-1/2" Center Outlet

The 70 Series muffler utilizes Flowmaster's patented Delta Flow technology and an enlarged case for improved sound control along with mileage and power gains. Perfect for use on trucks, SUV's, tow vehicles and high...

Product#: 9430G

1964-73 Mustang; Small Block; V8; Exhaust Manifolds

Cracked or missing exhaust manifolds can now be replaced! Exhaust Manifold for 1965-70 Mustangs with a 260, 289 or 302 Small Block Engine An authentic reproduction of the factory cast iron V8 exhaust manifolds. Each manifold...

Product#: HP177015

Heatshield Products; Header Armor Exhaust Manifold Heat Shield; w/ Wire; 1/2" Thick; (2) 18 X 24 Inch

Don't let the heat of your engine make you sweat! You can reduce under hood temperatures by up to 40 percent, keeping you cool at the track or on the street with the easiest to install and longest lasting heatshield blanket...

Product#: 55132S

Gibson CFT Superflow Muffler; Stainless Steel; 4" x 9" x 13" Oval Body; 2.5" Offset Inlet; 2.5" Offset Outlet.

Gibson's CFT Superflow muffler with Convergent Flow Technology actually tunes your exhaust by using resonance chambers, directional louvered tuning ports and angular induction to draw exhaust gases into the muffler and expel...

Product#: 55142S

Gibson CFT Superflow Muffler; Stainless Steel; 4" x 9" x 13" Oval Body; 2.5" Offset Inlet; 2.5" Center Outlet.

Gibson's CFT Superflow muffler with Convergent Flow Technology actually tunes your exhaust by using resonance chambers, directional louvered tuning ports and angular induction to draw exhaust gases into the muffler and expel...

Product#: 14266

Magnaflow 5"x 8" x 18" Polished Stainless Steel Muffler with 2.5" Offset Inlet / 2.25" Dual Outlets

Magnaflow's wide-open performance muffler outflows OEM chamber style mufflers by as much as 167%, reducing engine heat and back pressure that improves exhaust scavenging from the combustion chamber. The greater efficiency...

Product#: HP177005

Heatshield Products; Header Armor Exhaust Manifold Heat Shield; w/ Wire; 1/4" Thick; (2) 18 X 24 Inch

Don't let the heat of your engine make you sweat! You can reduce under hood temperatures by up to 40 percent, keeping you cool at the track or on the street with the easiest to install and longest lasting heatshield blanket...

Product#: 89000

Dynomax; Universal Header Dual Exhaust Pipe kit

Universal header dual exhaust kit features 2 1/4 in. diameter tubing and includes clamps and hangers. The kit exits in front of the rear axle and is compatible with Dynomax and Thrush turbo-style mufflers. {specs} {fitment}

Product#: PM20300T

Porter Muffler; Steel-Pac High-Flow Truck Muffler; 26" Overall Length; 3" Inlet/Outlet; Ceramic-Painted Steel

Porter Muffler Truck Muffler is handmade in America. Truck Mufflers are best used in a 2-into-1 exhaust system or high air flow application. Uniquely designed interior chamber is fitted with a gapped steel spring and packed...

Product#: PM20250SS

Porter Muffler; Steel-Pac Standard Muffler; 26" Overall Length; 2.50" Inlet/Outlet; Stainless Steel

Porter Mufflers standard mufflers feature 20" body length and are designed to create a slip fit lap joint with your mating exhaust tubing. All Porter Mufflers are non-directional, allowing them to be mounted in either...

Product#: HP372400

Heatshield Products; Lava Exhaust Wrap; 4" X 100 Foot Roll

Give your header and exhaust system a custom look with our Lava Exhaust Wrap. Made from crushed volcanic rock, our Lava Wrap has all the same benefits as exhaust wrap with that trick carbon fiber look and improved durability!...

Product#: F15925

Flowmaster; 3" Collector To 2.5" System; Header Collector Ball Flange Set

This header collector set takes the place of messy three-bolt, flange-type connections and allows for a leak-free and gasket-free ball-flange type connection. Made in USA Emission Note: 50- State Legal This part is legal for...