Product#: *FM1967

1967 Ford Mustang; Coupe to Fastback Sheet Metal Conversion; Kit

If you have a 1967 Ford Mustang Coupe but have always wanted a fastback, this will be your next project. This comprehensive Coupe to Fastback conversion kit supplies you with the necessary sheet metal and braces to convert...

Product#: 11220B-CM

1964-70 Mustang, 1967-68 Cougar; Full Trunk Floor Panel; Coupe, Fastback; EDP Coating

This is the full reproduction stamped steel floor pan assembly to fit 1964-70 Mustang and 1967-68 Cougar in EDP coating. The main structural part begins at the rear seat divider and goes back towards the taillight panel....

Product#: 27840UR

1967 Ford Mustang Fastback; Full Quarter Panel; Passenger Side; EDP Coated

Reproduction of the original quarter panel designed for use with 1967 Mustang Fastback models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...

Product#: 02228ARH

1967-68 Mustang; Upper Cowl Vent Cover Panel; Right Hand Drive Conversion

Reproduction of the original upper cowl vent cover panel designed for use with 1967-68 Ford Mustang models for use with right hand conversion. Each cowl vent grill panel is manufactured in stamped steel to original factory...

Product#: 11220D-CM

1964-70 Mustang; Complete Trunk Floor Panel; Convertible; EDP Coated

Reproduction of the original floor pan assembly designed for use with 1964-70 Ford Mustang Convertible models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: 50202A

1967-68 Mustang Fastback; Roof Panel; Silver Weld-Thru Coating

Reproduction of the original roof panel designed for use with 1967-68 Mustang Fastback models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...

Product#: 20125D

1967-68 Mustang; Door Shell; Drivers Side; EDP Coated

Reproduction of the original style complete door shell for use with 1967-68 Ford Mustang models. Each outer door shell is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: 20125C

1967-68 Mustang; Door Shell; Passenger Side; EDP Coated

Reproduction of the original style complete door shell for use with 1967-68 Ford Mustang models. Each outer door shell is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: 27840ZR

1967 Mustang Convertible; Full Quarter Panel; LH Driver Side

Reproduction full quarter panel for 1967 Mustang convertible models. Each quarter panel is manufactured in stamped steel to factory specifications. This quarter panel includes the lip that extends into the door jamb and the...

Product#: 27840YR

1967 Mustang Convertible; Full Quarter Panel; RH Passenger Side

Reproduction full quarter panel for 1967 Mustang convertible models. Each quarter panel is manufactured in stamped steel to factory specifications. This quarter panel includes the lip that extends into the door jamb and the...

Product#: M103BL

1964-70 Mustang; Rear Frame Rail; Convertible; Drivers Side; Weld Thru Coated

Reproduction of the original rear frame rail for use with 1964-70 Ford Mustang models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. The rear...

Product#: M105

1964-73 Mustang, Cougar; Complete Floor Pan; Convertible

Reproduction of the original complete floor pan designed for use with 1964-73 Ford Mustang and Mercury Cougar convertible models. Each floor pan is manufactured in stamped steel to original factory specifications featuring...

Product#: 40324GR

1967 Mustang; Tail Lamp Panel; Eleanor Style; For Sequential Cougar Tail Lamps

This tail lamp panel is used with sequential or Eleanor style (1967 Cougar) tail lamps on 1967 Mustangs. Will fit any 1967 Mustang as long as the correct Shelby style tail lamps are used. Each rear tail panel is produced in...

Product#: 04320B

1967-68 Mustang; Steel Dash Panel Assembly; Coupe/Convertible; without Knee Pad Holes

Reproduction stamped steel dash panel assembly for 1967-68 Mustang Coupe (without knee pad holes) or convertible. Features accurate stamping contours, cutouts, and mounting holes for the original dash trim parts to ensure...

Product#: 27840HR

1967 Ford Mustang; Full Quarter Panel; Coupe; LH

Reproduction of the original complete quarter panel for use with 1967 Mustang coupe models. Each quarter panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...

Product#: 02010A

1967-68 Mustang, Cougar; Lower Cowl Panel; EDP Coated

Reproduction of the original lower cowl panel designed for use with 1967-68 Ford Mustang, and Mercury Cougar models. Each cowl panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 16612BR

1967-68 Mustang; Hood Assembly; w/o Turn Signal Provisions; Bolt On; EDP Coated

Reproduction of the original hood assembly designed for use with 1967-68 Mustang models without turn signal provision. Each hood panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 27894H

1967-68 Mustang; Complete Rear Wheehouse Assembly; Coupe / Fastback; Drivers Side

Reproduction of the complete wheelhouse assembly designed for use with 1967-68 Ford Mustangs. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: 28161B

1967-68 Mustang 4 Piece B-Pillar Panel Set; 4 Piece Set

Reproduction B-Pillar panels for 1967-68 Ford Mustang models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance and fit. Replaces the...

Product#: 27894G

1967-68 Mustang; Complete Rear Wheehouse Assembly; Coupe / Fastback; Passenger Side

Reproduction of the complete wheelhouse assembly designed for use with 1967-68 Ford Mustangs. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: 17A940K

1967-68 Mustang; Racing Front Valance Panel

Fiberglass racing front valance panel for 1967-1968 Mustang models. Each racing valance panel is manufactured in quality fiberglass to the correct configuration. Can be used with stock bumper. Features two parking lamp holes...

Product#: 27849N

1967 Mustang; Quarter Panel Skin; Coupe, Convertible; w/Scoop Holes; RH Passenger Side

Reproduction of the original style outer quarter panel skin designed for use with 1967 Ford Mustang coupe and convertible models. This high-quality reproduction replaces the outer rear sheetmetal from the door jamb back to...

Product#: M107AL

1964-70 Ford Mustang; Front To Rear Full Floor Pan Section; Coupe/Fastback; LH

Reproduction of the original Mustang front to rear floor pan section for use with 1964-70 Mustangs. Covers area from 21" behind front seat to just past the area where the floor angles up to meet the firewall. Features all...

Product#: 53038A

1964-68 Mustang; Convertible Windshield Frame Header Roof Brace

Reproduction stamped steel windshield frame header or roof brace for 1964-68 Mustang convertible models. This is the steel structural support that makes up the top portion of the windshield frame, and that runs side-to-side,...

Product#: 40324BR

1967-68 Ford Mustang; Tail Lamp Panel; No Trunk Corners

Reproduction taillight panel manufactured using heavy gauge stamped steel. Mounts between the quarter panels at the rear of the car and provides a secure mounting point for the taillights and fuel filler pipe. Fits 1967-68...

Product#: 03408A

1964-68 Mustang; 1968-69 Cougar; Front Roof Brace; Coupe / Fastback

Reproduction of the original front hood brace designed for use with 1964-68 Ford Mustang coupe and Fastback models and 1968-69 Mercury Cougar models. Each roof brace is manufactured in stamped steel to original factory...

Product#: 11218AR

1964-70 Ford Mustang; Trunk Floor Pan; EDP Coated; RH

Reproduction of the original style floor pan manufactured in stamped steel for use with 1964-70 Mustangs. Each floor panel is manufactured in stamped steel to original factory specifications featuring correct contours for an...

Product#: M108R

1964-68 Mustang; Rear Half Floor Section Panel; Passenger Side

Reproduction of the original 1964-68 Mustang complete rear half floor section for RH passenger side side for convertible models. Located behind front seat. Original contour extends under lip of rear seat belt mounting on...

Product#: 27894B

1967-68 Ford Mustang; Quarter Wheelhouse Outer Panel; LH

If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with one of these inner or outer wheelhouse panels. More of a patch panel, these pieces can be used to replace small to medium...

Product#: 27894A

1967-68 Ford Mustang; Quarter Wheelhouse Outer Panel; RH

If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with one of these inner or outer wheelhouse panels. More of a patch panel, these pieces can be used to replace small to medium...

Product#: 27886A

1964-70 Mustang; Inner Quarter Wheelhouse Panel; Passenger Side; EDP Coated

If your Mustang has only minor rust problems within the wheelhouse area, you may be able to get by with the inner wheelhouse panel. More of a patch panel, this panel can be used to replace small to medium sized areas of rust...

Product#: M108L

1964-68 Mustang; Rear Half Floor Section Panel; Drivers Side

Reproduction of the original 1964-68 Mustang complete rear half floor section for LH drivers side side for convertible models. Located behind front seat. Original contour extends under lip of rear seat belt mounting on...

Product#: M103AL

1965-70 Mustang; Rear Frame Rail Section; Drivers Side

Reproduction of the original rear frame rail section designed for use with 1965-70 Mustang models. Manufactured to factory specifications out of 14 gauge steel, and measures 28" from the rear end of the frame rail towards the...

Product#: M107L

1964-70 Mustang; Front Floor Pan; LH Drivers Side; EDP Coated

Reproduction of the original front floor panel for use with 1964-70 Mustang models. Located under and forward of front seat, extending about 5" up toward firewall. This floor panel is cosmetically correct for 1964-1968...

Product#: M135B

1964-70 Mustang Coupe/Fastback; Rear Trunk Brace Support

Reproduction of the original rear trunk brace support designed for use with 1964-70 Mustang coupe and Fastback models. Each trunk brace support is manufactured in stamped steel to original factory specifications featuring...

Product#: 10780A

1964-70 Mustang; Rear Crossmember Support; EDP Coated

Reproduction rear crossmember support for 1964-1970 Mustang models. Each crossmember support is manufactured in stamped steel to OE specifications. Designed to strengthen the frame and create a rigid structure. Attaches to...

Product#: M112

Ford, Lincoln, Mercury Style; Floor Pan Plug; 2-7/8" x 4-5/8"

Galvanized and die stamped steel like the original. Can be used as a universal fit plug on practically any vehicle. The 2-7/8" x 4-5/8" floor pan plugs often need replaced from years of rust damage. Sold individually. Screws...

Product#: *84L020

Ford, Lincoln, Mercury; FLOOR PAN METAL PLUG; Pair; 3-3/4" x 2-3/8"

This is the oval metal plug that seals off the oval hole in the rear footwell area of the floor pan on 1979-1993 Ford Mustang and 1979-86 Mercury Capri. This plug is often rusted or completely missing. Sold individually....

Product#: 04320BRH

1967-68 Mustang Fastback; Steel Dash Panel Assembly; Right Hand Drive

This conversion panel is the perfect solution to a right hand drive conversion, or to replace a dash panel on export models. Reproduction of the original dash panel assembly designed for use with 1967-68 Ford Mustang right...

Product#: 27840VR

1967 Ford Mustang Fastback; Full Quarter Panel; Drivers Side; EDP Coated

Reproduction of the original quarter panel designed for use with 1967 Mustang Fastback models. Each panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...

Product#: 16612K

1967-68 Mustang; Fiberglass Hood; 1967 Shelby Style; Short Style; without Louvers

Reproduction of the 1967 Mustang Shelby style fiberglass hood with dual air inlet scoop, without side louvers. The air scoops are open. Get that Shelby GT350/GT500 look on your stock 1967-68 Mustang. Replaces the stock length...

Product#: 11220A-CM

1964-70 Mustang; Full Trunk Floor Panel; Coupe, Fastback; with Weld-Thru Coating

Quality reproduction of the original trunk floor pan assembly for use with 1964-70 Mustang Fastback and coupe models. Each trunk floor panel is manufactured in stamped steel to original factory specifications featuring...

Product#: 11220E

1964-70 Mustang; Complete Trunk Floor Panel; Convertible; Weld-Thru Coating

This is the full reproduction stamped steel floor pan assembly to fit 1964-70 Mustang Convertible in Weld-Thru primer. The main structural part begins at the rear seat divider and goes back towards the taillight panel....

Product#: M105HT

1964-68 Mustang, Cougar; Complete Floor Pan; Coupe & Fastback; EDP Coated

This complete floor pan for 1964-68 Mustang coupe or fastback and 1967-68 Cougar coupe models is manufactured to factory specifications. This stamped steel reproduction floor pan is built as a one-piece design featuring the...

Product#: 02010ARH

1967-68 Mustang, Cougar; Lower Cowl Panel; with Right Hand Drive; Export

RIGHT HAND DRIVE CONVERSION! Reproduction of the original lower cowl panel designed for use with 1967-68 Mustang and Cougar models with right hand drive. Each cowl panel is manufactured in stamped steel to original factory...

Product#: 02011B

1967-68 Mustang; Cowl Grill Panel Assembly; 2 Piece Set

Reproduction of the original cowl grill panel assembly designed for use with 1967-68 Ford Mustang models. Each cowl grill panel is manufactured in stamped steel to original factory specifications featuring correct contours...

Product#: 04320A

1967-68 Mustang Fastback; Steel Dash Panel Assembly; with Knee Pad Holes; EDP Coated

Reproduction stamped steel dash panel assembly for 1967-68 Mustang Fastback (with knee pad holes). Features accurate stamping contours, cutouts, and mounting holes for the original dash trim parts to ensure that you have an...

Product#: M103CL

1964-68 Mustang Fastback; Rear Frame Rail Complete; Coupe; Driver Side

Reproduction of the original rear frame rail for use with 1964-68 Ford Mustang coupe models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. This...

Product#: 16612CR

1967-68 Mustang; Hood Assembly; w/Turn Signal Cut-Out; Steel; Bolt On; EDP Coated

Reproduction of the original hood assembly designed for use with 1967-68 Mustang models with turn signal provision. Each hood panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 27840GR

1967 Ford Mustang; Full Quarter Panel; Coupe; RH

Reproduction of the original complete quarter panel for use with 1967 Mustang coupe models. Each quarter panel is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic...

Product#: 01610B

1967-68 Mustang, Cougar; Firewall Panel; Coupe; Fastback; EDP Coating

Reproduction of the original firewall panel for use with 1967-68 Ford Mustang and Mercury Cougar models. Includes the toe board panels along with the entire vertical panel that replaces the old or rusted original....

Product#: M103BR

1964-70 Mustang; Rear Frame Rail; Convertible; Passenger Side; Weld Thru Coated

Reproduction of the original rear frame rail for use with 1964-70 Ford Mustang models. Each frame rail is manufactured to original factory specifications replicating the original in quality, design, and fitment. The rear...

Product#: 27894Q

1967-68 Mustang; Complete Wheelhouse Assembly; Convertible; Passenger Side; EDP Coated

Reproduction of the original complete wheelhouse assembly designed for use with 1967-68 Mustang convertible models. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 27894R

1967-68 Mustang; Complete Wheelhouse Assembly; Convertible; Drivers Side; EDP Coated

Reproduction of the original complete wheelhouse assembly designed for use with 1967-68 Mustang convertible models. Each wheelhouse panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: M137

1964-70 Mustang; Seat Platform; Convertible; One Piece Design

Reproduction of the original seat platform designed for use with 1964-70 Ford Mustang convertible models. Each seat platform is manufactured in stamped steel to original factory specifications featuring correct contours for...

Product#: 02228A

1967-68 Mustang; Cowl Vent Grill Panel; EDP Coated

Reproduction of the original cowl top vent grill panel designed for use with 1967-68 Ford Mustang models. Each cowl vent grill panel is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 16005DR

1967 Ford Mustang; Front Fender; EDP Coated; LH Driver Side

Reproduction front fender for 1967 Ford Mustang models. Each front fender is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance and fit. Comes with a black...

Product#: 40110BR

1967-68 Mustang; Trunk Lid; Coupe or Convertible; EDP Coated

Reproduction of the original trunk lid designed for use with 1967-68 Ford Mustang coupe or convertible models. Each trunk lid is manufactured in quality stamped steel replicating the original in design, appearance, and...

Product#: M137A

1964-68 Mustang, Cougar; Front Seat Platform Panel; Coupe/Fastback; One-Piece; Weld Thru Coated

Reproduction of the original seat platform designed for use with 1964-68 Ford Mustang coupe and Fastback models. Each seat platform is manufactured in stamped steel to original factory specifications featuring correct...

Product#: 16005CR

1967 Ford Mustang; Front Fender; EDP Coated; RH Passenger Side

Reproduction front fender for 1967 Ford Mustang models. Each front fender is manufactured in stamped steel to original factory specifications featuring correct contours for an authentic appearance and fit. Comes with a black...