Product#: 13757

1965-69 Impala, Camaro, Bel Air, Firebird; Hood Insulation Fastener; Black Nylon

Replacement black nylon 2" square head hood insulation retainer is just what your classic vehicle needs to keep your original hood insulation where it belongs...attached to the hood. This retainer is a service replacement for...

Product#: 3910667

1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; LH; Driver Side

Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...

Product#: 3907626

1967-81 GM Hood Hinge Spring ; Each

Reproduction of the original hood hinge spring designed for use on various GM vehicles. Each spring is manufactured to replicate the original in quality and design. Will fit and install as original and features OE tension...

Product#: 3857882

1967-81 Camaro, 1965-68 Impala, 1947-72 Chevy/GMC truck; Hood Latch Pop-Up Spring

Reproduction hood pop-up spring for 1947-55 and 1962-72 Chevy/GMC truck, 1967-81 Camaro, 1965-68 Impala, Bel Air, Biscayne, Caprice, and 1968 Chevelle, El Camino models. Measures 3-3/4" long and features a black EDP coating...

Product#: 3903974

1967 Impala, 1968-69 Camaro; SS Hood Louver Drains; Pair; Made in the USA!

Reproduction of the original Super Sport hood louver drain tubes for use with 1967 Impala SS, and 1968-69 Camaro Super Sport models. These drain tubes install under the hood substructure and are designed to direct water from...

Product#: K1005

Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 8 Piece Set

OER Authorized, direct replacement hood hinge to fender bolt set for various GM vehicles. This kit consists of a quantity of 8 black phosphate coated (9/16" head size) hex washer head SEMS body bolts with 3/8"- 16 x 1" specs....

Product#: K1006

Hex Head SEMS Body Bolt Set; 3/8"-16 x 1"; For Hood Hinges; 10-Pieces

Black phosphate coated hex head bolts with washer. Measures 3/8-16 x 1" SEMS with 1" outside diameter to fit a variety of applications, including the hood latch on 1970-81 Firebird, and 1973-80 Chevrolet or GMC truck, among...

Product#: *R1383

Hood Insulation Fastener Set; 5/16" Stem Diameter; 3/4" Stem Length; 1-3/4" Head Diameter; 20-Pieces

Replacement black nylon 1-3/4" hood insulation retainer is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models...

Product#: A1015

1970-2002 GM; Hood Insulation Fastener; Each

Replacement black nylon hood insulation fastener is just what your GM vehicle needs to keep your original hood insulation where it belongs... attached to the hood. This retainer is a service replacement for most models. It...

Product#: 3910668

1965-69 Impala, Camaro, Nova, Firebird; Hood Hinge; RH; Passenger Side

Reproduction of the original hood hinge assembly designed for various GM models. Each hood hinge is manufactured from stamped steel assuring a quality replacement. We recommend replacing the hood spring when installing a new...

Product#: K555

1958-77 GM; Hood Adjuster Bolt and Nut Set ; 5/16"-18 x 1-3/8"; Various Models

Reproduction of the original hood stop bolt and nut set designed for use on various 1958-77 GM models. This bolt and nut set will keep the hood adjusted to the proper height. These 5/16"-18 x 1-3/8" bolts include the correct...

Product#: K638

Hood Pin Rubber Gasket; Each

Reproduction hood pin rubber gasket found on models with hood pins. Each gasket is die-cut to proper dimension. Will also fit a wide variety of aftermarket hood pins. Sold individually. Use as required. Check measurements...

Product#: DE050129

DEI Boom Mat; Under Hood Black Thermal Acoustic Lining Sheet; Trim to Fit; 32" x 59" Sheet

DEI Black Under Hood thermal acoustic lining. Designed specifically for under hood applications, this lining will greatly reduce the heat, noise, and vibration coming from your engine compartment. This black self adhesive...

Product#: CB46303

1965-67 Impala/Full Size; Solid Arm Billet Hood Hinges; Steel Hood; Black Anodized Finish

Replace your functional but unsightly original hood hinges with a pair of Ringbrothers premium quality billet hood hinges. Features: Machined from 6061-T6 billet aluminum Ball bearing pivot joints Gas shocks Direct...

Product#: CB46301

1965-67 Impala/Full Size; Solid Arm Billet Hood Hinges; Steel Hood; Natural Finish

Replace your functional but unsightly original hood hinges with a pair of Ringbrothers premium quality billet hood hinges. Features: Machined from 6061-T6 billet aluminum Ball bearing pivot joints Gas shocks Direct...

Product#: CB46401

1965-67 Impala/Full Size; Air Frame Style Billet Hood Hinges; Steel Hood; Natural Finish

Replace your functional but unsightly original hood hinges with a pair of Ringbrothers premium quality billet hood hinges. Features: Machined from 6061-T6 billet aluminum Ball bearing pivot joints Gas shocks Direct...

Product#: CB46302

1965-67 Impala/Full Size; Solid Arm Billet Hood Hinges; Fiberglass Hood; Natural Finish

Replace your functional but unsightly original hood hinges with a pair of Ringbrothers premium quality billet hood hinges. Features: Machined from 6061-T6 billet aluminum Ball bearing pivot joints Gas shocks Direct...

Product#: MS14743BA

1965-67 Impala; Bel Air; Biscayne; Hood Hinges; Kinetic; Billet Aluminum; with Stainless Steel Gas Struts; Gloss Black Anodized Finish; with Stainless Mounting Hardware

Eddie Motorsports newly designed Kinetic hood hinge features form and function in a CNC precision machined T-6061 billet hinge. The new Kinetic hinge is a custom alternative to the inferior O.E. stamped steel hinge. Mounting...

Product#: MS14743CA

1965-67 Impala; Bel Air; Biscayne; Hood Hinges; Kinetic; Billet Aluminum; with Stainless Steel Gas Struts; Clear Anodized Finish; with Stainless Mounting Hardware

Eddie Motorsports newly designed Kinetic hood hinge features form and function in a CNC precision machined T-6061 billet hinge. The new Kinetic hinge is a custom alternative to the inferior O.E. stamped steel hinge. Mounting...

Product#: MS14743CL

1965-67 Impala; Bel Air; Biscayne; Hood Hinges; Kinetic; Billet Aluminum; with Stainless Steel Gas Struts; Bright Clear Finish; with Stainless Mounting Hardware

Eddie Motorsports newly designed Kinetic hood hinge features form and function in a CNC precision machined T-6061 billet hinge. The new Kinetic hinge is a custom alternative to the inferior O.E. stamped steel hinge. Mounting...