29 Piece Clecos Sheet Metal Fastener Kit
This Cleco sheet metal fastener kit contains everything you need to secure sheet metal panels during the fit and alignment stage. The pliers can be used with all standard spring loaded fasteners and clamps. Kit includes: One...
Auto Rotisserie EZ Spin; with Jacks
The Auto Rotisserie E-Z Spin features 12 multi-angle postioning stops every 30 degrees, HD swivel casters and rotates a full 360 degrees. It's work height is adjustable from 44" to 59", center line is adjustable from 10" to...
Blair Tools; Holcutter Set; 1/8" D.O.C.
Holcutters are not hole saws. They are precision ground, heat treated tools that easily cut through the stock rather than ripping, tearing, and pushing thru as do typical hole saws. They can produce holes 3 times faster and...
3/4" x 1" Individual Side Clamps
This clamp can be applied in a fraction of the time required for ordinary screw clamps and assures uniform pressure by eliminating hand tightening. Provides 70 lbs. of clamping pressure and uses standard Cleco Pliers. Sold...
Glass Molding Clip Installation Tool
This handy tool makes a difficult job much easier. This tool removes or installs the clips found on most exterior moldings and helps to avoid damage to the moldings or the surface that they are mounted to.
The auto hood puller is designed for easy pulling and mounting of the hood. Helps to eliminate scratches and dings to the paint on the hood and fenders. To be used with any engine pulling hoist.
Great tool to have when replacing your OEM or aftermarket steering wheel. Allows for easy removal, can be used for almost any model and includes instructions.
To test the quality of a paint job the Pro Gauge can't be beat! Basically, it's a device which measures paint thickness. Factory paint is usually four to five mils in thickness (a mil is one thousandth of an inch). By using...
Windshield Molding / Door Handle Clip Remover
Specialty pliers for removing door handle clips and chrome molding on most windshields and rear glass. Jaws slip under door handle without damage to panel material, and offset handle permits easy access to molding clips.
Blair Tools; Rotabroach 8mm-20Mm Metric Cutter Set; 1/4" Depth of Cut
For precision hole making in sheet metal and frame materials up to 1/4" thick, Rotabroach® annular cutters make clean, burr-free, round holes with no deforming of stock or damage to the surrounding material. Ideal for...
Blair Tools; Rotabroach 8mm-20Mm Metric Cutter Set; 1/4" Depth of Cut
Classic $83.99 set
Body Shims 1/16" Thick, 1-1/4" x 1-1/8" with 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
When replacing sheet metal one of the most essential items are shims. Shims are important when it comes to aligning front end sheet metal. Please check your originals to be sure your ordering the correct shims necessary for...
Body Shims 1/16" Thick, 1-1/4" x 1-1/8" with 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
Classic $17.99 set
Body Shims 1/8" Thick, 1-1/4" x 1-1/8" With 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
When replacing sheet metal one of the most essential items are shims. Shims are important when it comes to aligning front end sheet metal. Please check your originals to be sure your ordering the correct shims necessary for...
Body Shims 1/8" Thick, 1-1/4" x 1-1/8" With 3/8" Bolt Slot. Zinc Plated, 50 Piece Set
Classic $22.99 set
Door Adjustment Tool with Handle
When it comes to adjusting the door hinges so they accurately align with the body of the car, you might find most novice restorers frustrated. You can now easily adjust the hinges without the aggravation of trying to align by...
Blair Tools; 3/8" Spotweld Cutter Set; With Skip Proof Pilot
When you have a lot of spotwelds to remove, step up to the premium spotweld cutters for longer life in today's high-strength body steels. These cutters have a heavier wall (.090") for extreme durability and two step geometry...
Vice Grip 1" Jaw Flange Pliers
After cutting out rusted areas on fenders or quarter panels, preparing the panels with an offset flange will produce a clean, flush fit. The wide jaws work into corners and saves time on straightaways. Work on up to 18 gauge...
Universal Molding Release Tool
Slide tool left or right under the molding until it hooks a retaining clip, then just rock the tool with a twist of the wrist to release the clip. Heat treated, high-carbon steel.
The ultimate solution for removing door pins fast. Drives out even stubborn hinge pins. Works on all GM cars with removable hinge pins. Includes pin puller to remove loosened pins.
Super Seam Buster (For Air Hammers)
This heavy-duty chisel allows you to easily separate spot welded or bonded panels. Save up to 15 minutes per panel replacement. Great for quarter panels, rocker panels and other pinch welded areas. Sharpened on two edges, the...